| Menu 0 - Last trigger statistics | |
|---|---|
| 0.1 DTMF received | Displays DTMF code as it was received |
| 0.2 DTMF decoded | Displays DTMF code as it was decoded |
| 0.3 LFC time decoded | Length [ms] of LFC carrier as it was detected |
| 0.4 Last activation | Time [s] since last trigger activation |
| 0.5 Trigger status | Mx0 missing chars; Wr wrong chars; Ux unrecovered; Lc LFC error |
| 0.6 Triggered spot | Triggered spot number as its index in the filename on removable media |
| 0.7 Last time played | Last spot playing time, including all delays from the system |
| 0.8 Maximum playing time | Maximum playing time of triggered spot. It is defined for Code 1/2 in 8.5 and 8.6 and for Code 3 (manual trigger) is hard-set to 30s. After this time, playing (and transmitting) is forced to stop for security |
| Menu 1 - General statistics | |
|---|---|
| 1.1 Code_001 activated | Code 001 triggers since last reboot or since Up-time 00:00:00:00 |
| 1.2 Code_002 activated | Code 002 triggers since last reboot or since Up-time 00:00:00:00 |
| 1.3 DTMF missing chars | Missing chars since last reboot or since Up-time 00:00:00:00 |
| 1.4 DTMF wrong chars | Wrong chars since last reboot or since Up-time 00:00:00:00 |
| 1.5 Allowed errors exc. | Allowed errors exceeded since last reboot or Up-time 00:00:00:00 There are 12. chars in a Code and user can define how many of them can be wrong/missing by setting variable “DTMF allowed errors in 3.4 |
| 1.6 LFC errors | LFC errors since last reboot or Up-time 00:00:00:00 |
| 1.7 False characters | False characters detected since last reboot since Up-time 00:00:00:00 They are defined as a group of chars received in number less than 3 in period less than 4 sec. Those are NOT a part of statistics! |
| 1.8 Up-time | System uptime; resets while rebooting or powering-up |
| Menu 2 - Transmitter settings | |
|---|---|
| 2.1 Tx idle frequency | Transmitter “idle" frequency [kHz]; Means PLL frequency when transmitter is off. This is used for parking PLL off the receiving frequency to avoid interfering with the FM receiver. Range from 87500 to 108000 |
| 2.2 Tx out frequency | Transmitter “broadcast” frequency [kHz]; Range from 87500 to 108000 |
| 2.3 Power soft attack | If set to “ON”, Tx power rises slowly to desired value as preset in 2.4; Usually rises for a few seconds to reach desired value. If set to “OFF”, Tx power starts in full within a few hundred miliseconds. |
| 2.4. Output power | Desired output power regulated and measured at the transmitter output |
| 2.5 Transmitter volume | Transmitter audio volume, regulated at input of the FM modulator; For maximum volume set to ‘32’ |
| 2.6 Fallback power | Transmit power used when an antenna issue gets detected; Measure return power value exceeds value in 9.27.2; Note: this value does not represents watts or SWR, its just na A/D value representation. Value of “10” equals roughly SWR 1,5 |
| Menu 4 - Receiver settings | |
|---|---|
| 4.1 Rx frequency | Receiver frequency, FM receiver frequency to listen for code |
| 4.2 Rx AGC | Receiver automatic gain; 0 = automatic |
| 4.3 Rx pre-amp | Receiver preamplifier ON/OFF |
| 4.4 Rx pre-amp gain | Rx preamplifier gain; +9db/+6db |
| 4.5 Rx volume | Receiver volume; 63 = max |
| 4.6 Rx force mono | If set to “on”, receiver is set to MONO |
| Menu 5 - Sytem settings | |
|---|---|
| 5.1 Factory settings | To load factory settings, use following sequence: |
| - set "Factory settings" to 1 | |
| - save settings in menu 5.6 | |
| - reboot device | |
| 5.2 Power save | Activate power saving in [s]; 0 = off; 255=maximum (Note: this action does not affect decoding and other functionality) |
| 5.3 Wake-up on trigger | If set, module wakes from “Power save” mode when trigger is activated |
| 5.4 Auto lock | Automatic screen lock in [s]; 0 = off; 255 = max |
| 5.5 Lock when transmitting | Automatically lock the screen when transmitting to prevent issues |
| 5.6 Save settings | Save all settings to internal Flash memory |
| Menu 6 - Advanced settings | |
|---|---|
| 6.1 Ventilator assign | Assign all fans to adequate temperature sensors and sets their priority For detailed settings check “SubMenu 20: Ventilator assign procedure” in attachment |
| 6.2 Banned codes | Sometimes there are DTMF characters used in third party airings. If such codes appear periodically, they may be put on the blacklist to remove them from “wrong codes” statistics |
| 6.2.1 Blacklist enable | Blacklist record activating. Each position represents bit in entered value; left justified. 0 = all unused; 1 = first allowed; 2 = second allowed; 3 = first and second allowed; 9 = first and fourth allowed |
| 6.2.2 – 6.2.6 Banned codes | Enter DTMF codes to be banned as they appears in the decoder |
| 6.3 Adv.Rx/MP3 settings | Some tunning variables for receiver and MP3 player |
| 6.3.1 High freq. cut off | Lowpass filter for FM receiver, use values 0 (off) to 6 |
| 6.3.2 Chan. Filter bandwith | Bandwith for filter, use values 0(off) to 6 |
| 6.3.3 Deemphasis | Deemphasis 75us for EUROPE, 50us for US countries |
| 6.3.4 Force FM stereo | Force FM stereo output as long as stereo carrier detected |
| 6.3.5 MP3 volume | MP3 player output volume, maximum value 35 |
| 6.4. Timing functions | Functions that rely on time |
| 6.4.1 Hibernation ON | Start time for mode when triggering is OFF, low power mode |
| 6.4.2 Hibernation OFF | End of low power mode, triggering activatted |
| 6.4.3 Daily report at | The time for full report sending, this time should be inserted within Hibernation time 6.4.1 and 6.4.2 |
| 6.4.4 Force online trigger | Trigger report after playing stops; 0 = off; time[s] = delay after playing |
| 6.4.5 Automated trig. Period | Period [s] for repeated playing and transmitting spot in 6.5 |
| 6.4.6 Set D/T | Manually set date/time; value is stored automatically. GSM overrides. |
| 6.5 Auto trigger spot | Number of the spot to be played if automated trigger 6.4.5 gets activated 000 = off; 001 = play spot 001_xxx.mp3 |
| 6.6 Display calibration | Enter menu for TFT display touch calibration procedure |
| Menu 7 - Security and protection | |
|---|---|
| 7.1 Report temp. alarm | Not supported in current version |
| 7.2 Force Tx_FAN2&4 ON | Minimal value of FAN2 and FAN4 power when transmitter is ON |
| 7.3 Shutdown temperature | If any temperature reaches this value, transmitter shuts down |
| 7.4 Shutdown humidity | If the humidity reaches this value, transmitter shuts down |
| 7.5 Security code enable | Enable locking screen PIN |
| 7.6 Security code | Security PIN code (default 123) |
| Menu 8 - Playback settings | |
|---|---|
| 8.1 Code_1 DTMF spot | Number of the spot to be played if Code1 gets activated |
| 8.2 Code_1 LFC spot | Number of the spot to be played if Code1 and LFC carrier get activated |
| 8.3 Code_2 DTMF spot | Number of the spot to be played if Code2 gets activated |
| 8.4 Code_2 LFC spot | Number of the spot to be played if Code2 and LFC carrier get activated |
| 8.5 Code_1 max. length | Maximum playing length of spot 001_xxx.mp3 [s] |
| 8.6 Code_2 max. length | Maximum playing length of spot 002_xxx.mp3 [s] |
| Menu 9 - Miscellaneous settings | |
|---|---|
| 9.1 Event browser | Show full log of trigger activities as they were saved in FLASH memory. For detailed description see Submenu “24 - Event browser usage" |
| 9.2 Logger settings | Quick access to the serial console log with main commands |
| 9.2.1 !EE! | Perform erasing trigger log and resets pointers |
| 9.2.2 N/A | Not supported in current version |
| 9.2.3 RST | Resets GPRS module, full reset takes up to 30s |
| 9.2.4 CMD | Used to manually enter command number. See “Serial console commands and logging” attachment for details |
| 9.2.5 K? | Command “K”; K = 0 for simplified logs; K = 1 for detailed logs |
| 9.2.6 CLR | Clears LOG screen and reset pointer |
| 9.3 Connection settings | Displays GPRS current settings by clicking to particullar black frame (Note: configuration cannot be performed from this menu. Use console commands to configure GPRS module) |
| 9.4 Extra events | Various activities settings |
| 9.4.1 GSM synchronize | Hour and minute of the day when time synchronization was performed |
| 9.4.2 Force report from | Setup first and last index of event to be transmitted manually |
| 9.4.3 FM_Rx watchdog | How many seconds of silence from FM are allowed before reboot FM |
| 9.4.4 RS485 watchdog | Number of non-response seconds from temperature sensors allowed |
| 9.4.5 RF Tx watchdog | Number of seconds to wait for response from Tx before reboot module |
| 9.4.6 MP3 silence stop | Number of silence seconds from MP3 before playing is forced to stop |
| 9.5 Advanced Tx settings | Special features for transmitter tuning and special modes |
| 9.5.1 PLL to TxF time | Delay to activate transmitter allowing PLL tunning from idle to Tx freq. |
| 9.5.2 Ret. power to failsafe | Returned power that activates failsafe transmit power |
| 9.5.3 Ret. power to Tx_off | Returned power that deactivates transmitter |
| 9.5.4 RadioBroadcastPower | Not supported in current version |
| 9.5.5 RBC idle power | Not supported in current version |
| 9.5.6 Tx Lo Volt lock | Undervoltage protection; below this value, Transmitting is inhibited 110=11V |
| 9.6 BlackBox ID | Enter value in decadic form; displays in HEX |